When something goes wrong with the wiring in a Maize home, the symptom is usually obvious and the cause usually isn't. A breaker that keeps tripping, an outlet that stopped working, a light that flickers every time the refrigerator kicks on: each of those points somewhere specific, and finding that spot is where the work starts. We handle electrical repairs and installations throughout Maize and the surrounding area, and we're available every day from 7:30 AM to 10:00 PM.
Call (316) 294-4289 for a quote.
Maize is a town where most of the housing stock is residential and a good share of it has been added onto or updated over the years. That means wiring that doesn't always match the original plan, panels that were sized for a smaller load, and circuits that have been extended without always being documented. We scope the job on the call, confirm the price before we schedule, and show up ready to work. Whether you're a homeowner dealing with a fault you can't pin down or a landlord getting a rental unit ready between tenants, we cover the electrical side completely.
Staying ahead of electrical problems keeps your home safe, and most of what people call about falls into a handful of recognizable situations. Below is a look at the specific job types we handle most often in this area, and what each one actually involves.
A home that started at 100-amp service and has since added a second HVAC circuit, a finished basement, or a home office often runs short on capacity in ways that show up as nuisance trips and limited room for new circuits. A service upgrade replaces the panel, the service entrance, and sometimes the meter connection to bring the home up to a higher amperage. The work starts with a load calculation so the new service is sized correctly, not just larger. Subpanel installation is part of the picture when a detached garage or a large addition needs its own distribution point.
Outdoor lighting covers more ground than a single fixture on a porch. Security lights, motion-sensor fixtures, landscape lighting along walkways and driveways, and soffit or eave lighting all require weatherproof installation, correctly rated wire for outdoor runs, and sealed junction boxes that hold up over time. We handle the circuit side completely, from the panel to the fixture, and we make sure the installation meets code for exterior work before we leave.
A dryer, range, or large refrigerator draws more current than a shared circuit is rated to carry, and code requires most of them to have their own circuit. Adding a dedicated circuit means running the right wire gauge from the panel, installing the correct outlet, and confirming the panel has capacity for the added load. For a kitchen remodel or a laundry room addition, that planning happens before the walls close up, not after.
Running power to a detached structure is a different job from adding an outlet inside the house. It involves a trench or an overhead run, the right wire type for the application, a subpanel or disconnect at the structure, and grounding at both ends. Electric gate operators add a control circuit and sometimes a low-voltage component alongside the power supply. We scope these jobs on the call and confirm what the run involves before anything is scheduled.
Beyond those four, we handle the full range of residential electrical work: troubleshooting and diagnostics for faults that aren't obvious, circuit installation for additions and remodels, ceiling fan installation, knob-and-tube replacement in older homes, and service-entrance and meter upgrades when the utility connection needs to be brought up to current standards.
Permit requirements vary by jurisdiction, and this page isn't the place to state a local rule as fact. What is generally true is that work involving the service entrance, a panel replacement or upgrade, new circuits, and most wiring inside walls requires a permit and an inspection before the work is considered complete. Replacing a device like an outlet or switch in kind typically does not.
We tell you if a permit is needed. We name the fault plainly. You decide the fix.
When a permit is required, we handle the filing. The permit is factored into the scope on the call, so it isn't a surprise that shows up after the work is agreed to. Inspections are coordinated around the job timeline so the work doesn't sit waiting. Work in this area gets done to the code inspectors here actually enforce, and that's the standard we hold to on every job regardless of whether an inspection is required.
Commercial electrical work in a town this size tends to involve small retail spaces, offices, and light industrial buildings rather than large multi-tenant complexes. The planning challenge is the same regardless of scale: keeping the parts of the building that need to stay live exactly that way while the work gets done. That means identifying which circuits can be isolated, which loads need to stay energized, and how the job gets sequenced so the business doesn't lose more than it has to.
Panel work and service upgrades for commercial properties often go smoother outside business hours, when equipment can be de-energized without affecting operations. We work around the schedule that makes sense for the property. If the job involves the main service or the service entrance, we coordinate the utility outage window and confirm the timing before the work starts. The scope and the price are settled on the call, not after the crew is on site.
The gap between tenants is the easiest window to do electrical work that would otherwise mean working around occupied space. No coordination with residents, no scheduling around someone's work-from-home day, and full access to the panel and every circuit. For a landlord in Maize, that window is the time to address the outlet that never worked right, the bathroom GFCI that's been a complaint, or the panel that needs an honest look before the next tenant moves in.
Access is straightforward when a unit is vacant. We confirm what's needed on the call, schedule the visit for a time that works around the turnover timeline, and get the work done before the unit is occupied again. If the inspection turns up something that wasn't on the original list, we explain it before we add it to the scope.
Good electrical work isn't complicated, it's just done right, and part of doing it right is giving you a real number before anything is scheduled. When you call about electrical work in Maize, you get the price on the call. That price is based on what the job involves: what the fault turns out to be, what has to be opened up to reach it, and whether the existing circuit or panel can carry what's being added.
Three things move a quote in one direction or another. The first is the fault itself. A tripped GFCI upstream is a different job from a wiring fault inside the wall. The second is access. A circuit in a finished basement takes longer to reach than one in an unfinished utility room. The third is panel capacity. If a dedicated circuit or a new load requires more capacity than the current panel carries, that becomes part of the conversation before the work starts, not after.
You get a plain answer on repair versus upgrade before anything is agreed to. The price is confirmed before we schedule. If something changes once the work is opened up, we explain it before we continue.
A flickering light and a full rewire start the same way: a call, a clear scope, and a confirmed time. For routine work, the appointment is set on the call and confirmed before the visit. For a problem that won't keep, we take short-notice work and the schedule is checked when you call. Ask what's available and you'll get a straight answer.
For tenants or businesses that need to stay operational, we plan the visit around the access and outage window that works. If the work involves the main panel or the service entrance, we confirm what will be de-energized and for how long before the day of the job. You get a call before the visit to confirm what's happening and what to expect. No guesswork. No shortcuts. No loose ends. Where a Maize job fits is easier to see on the services page.
We cover Maize and the surrounding communities throughout Sedgwick County. That includes Colwich, St. Marks, Valley Center, Park City, and Bentley, along with the rural properties and acreages between them. If you're in the area and need electrical work, the call reaches someone who can scope the job and confirm availability.
We're available every day from 7:30 AM to 10:00 PM. Residential, commercial, and rental properties are all covered.
Call (316) 294-4289 for a quote.
Responsibility for the damage is a matter between the trades and the property owner. Our role is to assess and repair the damaged wiring so the system is safe and functional again. We document what we find and what the repair involves, which gives you a clear record of what happened and what it cost to fix.
We work with whoever is coordinating access, whether that is the property manager, a tenant, or a building contact. The key is knowing who will be on site, when access is available, and which circuits or areas need to be shut down during the work. Confirm those details on the call and we plan the visit around them.
Homes in this area vary widely in age, and older construction sometimes turns up wiring that was installed under earlier standards. Knob-and-tube wiring, aluminum branch-circuit wiring, and undersized panels are all conditions that change how a job is scoped and what the right fix looks like. When you call, we ask about the home's age and what you're seeing, and we factor that into the scope before anything is scheduled.
If the diagnostic turns up a condition that wasn't part of the original scope, we explain it before we add anything to the job. The price for additional work is confirmed before we continue. Nothing gets added without a conversation first, and you always know what you're agreeing to before the work proceeds.
We do. Running power to a detached structure involves its own set of considerations: the type and route of the supply run, grounding at both ends, and whether the structure needs a subpanel or a simple disconnect. We scope that work on the call and confirm what the job involves before we schedule a visit.
The meter is the dividing line. Everything from the meter into the home is our scope. Everything from the meter back to the utility's equipment is their responsibility. When we diagnose a fault, we start by establishing which side of that line the problem is on, and if it turns out to be a utility issue, we tell you that directly rather than billing for work that would not fix it.
Pool and pond equipment requires circuits rated for outdoor and wet-area use, GFCI protection, proper bonding of the water and metal components, and in some cases a disconnect within sight of the equipment. We handle the electrical supply and bonding side of pool and pond installations. The equipment itself is a separate scope.
We scope as much as possible on the call and give you a number before anything is scheduled. For larger jobs, the price may be confirmed or adjusted once we see the panel and the property in person, but we do not leave you without a figure to work with before the visit. The goal is a clear price before the work starts, not after.
An electrical problem that seems minor has a way of staying minor right up until it doesn't. A breaker that trips occasionally becomes one that trips constantly. An outlet that's warm to the touch is telling you something the wall isn't showing yet. Putting a call off doesn't change what the wiring is doing.
Call (316) 294-4289 and we'll tell you what the job involves and what it costs before anything is scheduled.
We cover the full range of electrical work across Maize and Sedgwick County, and the call is answered by someone who knows the trade and can scope the job on the phone.
See the whole of our full coverage area. Electrical work also reaches these towns: Valley Center, Park City, Goddard, Bel Aire, Oaklawn-Sunview.
Below is a breakdown of the electrical work we handle for homes, rentals, and businesses in Maize and across Sedgwick County. Each service is listed with what it covers, who it fits best, and a practical note to help you know what to expect before you call. If you have a question about a specific job, call us and we will walk through what it involves and give you a price before anything is scheduled.
| Service | Scope of Work | Ideal For | What to Keep in Mind |
|---|---|---|---|
| Electrical Safety Inspections | Panel and service-entrance review, GFCI and AFCI protection check, Grounding and bonding assessment, Outlet and switch condition survey | Buyers, sellers, landlords, or homeowners who want a clear picture of what their wiring is doing | An inspection before closing on an older Maize home can surface wiring conditions that are not visible during a standard home inspection. |
| Outlet & Switch Installation | GFCI and AFCI outlet installation, Standard outlet replacement, Dimmer and smart switch installation, Grounding and bonding verified | Homeowners adding outlets, upgrading to code-required protection, or replacing worn devices | GFCI protection is required in kitchens, bathrooms, garages, and outdoor areas. AFCI protection is required in bedrooms and living spaces under current code. |
| Electrical Panel & Service UpgradesMost Popular | 100-amp to 200-amp service upgrade, Subpanel installation, Meter and service-entrance work, Load calculation and utility coordination | Homes adding EV chargers, finishing a basement, or running modern appliances on an undersized panel | Many Maize homes were built with 100-amp panels that cannot support today's household load. A 200-amp upgrade gives the panel headroom for current and future demand. |
Call (316) 294-4289 and we will walk through what your job involves, give you a straight answer on what it costs, and get it on the schedule.
(316) 294-4289